Do Not Sell My Personal Information Jump to content


isrod

Members
  • Posts

    22
  • Joined

  • Last visited

Profile Information

  • First Name
    Rod Angel
  • Lexus Model
    IS250 XE20
  • Year of Lexus
    2006
  • UK/Ireland Location
    Lancashire

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

isrod's Achievements

Explorer

Explorer (4/14)

  • First Post
  • Collaborator
  • Conversation Starter
  • Week One Done
  • One Month Later

Recent Badges

10

Reputation

  1. lexusownersclub.co.uk/forum/topic/128673-spark-plugs/#comments been there done that
  2. Had my mot Monday and it failed on poor rear right brake the headlamps had no issue so cracking is ok considering it's year , I have had the car 4yrs now and in that period I have refurbed the caliper on the right rear twice this time I treated her to a new one 60 quid off eBay and an hour to fit passed test for 100 quid happy chappy
  3. hi all, just to ask the forum folk does the 2006 IS250 AUTO have a gearbox oil cooler ? Is it built in to the radiator ie does actual trans oil run through the radiator itself or does it take coolant to the box ? Going to have to change my rad as its starting to corrode and wondered if it would affect the gearbox oil level .
  4. ok so I had everything done and gassed up two weeks later no gas not happy the seal in the s/hand pump failed luckily the seller refunded me fully so I have bitten the bullet and bought brand new with a new condenser and dryer so time to fit them and get it regassed again. Used a company called CoolpartsUK got both items for £306 delivered from Tyneside moral s/hand not always the best option will report back on progress might even post pics.
  5. My headlamps have gone foggy as they do so I cleaned with a rubbing compound and polished up and they look far better but in the lens the plastic/glass cover have very fine cracks/marks in them which polishing doesn't seem to move it almost looks as if it is on the inside of the lens has anyone come across this and found a solution?
  6. The trouble with carbon clean is they put it through the injectors in most cases and the IS250 engine is direct injection ie the fuel is injected via a separate port so the cleaner does not actually get on to the inlet and exh valves so it imo a waste of time, the only way to get to the valves is through the inlet manifold which involves stripping to the level in the pics and worse case head removal the Americans do have it harder than us. But quality fuel and proper oil changes with the correct oil low sulphur, low ash type is the way to go . I always use Q8 Formula Special D1 5W-30
  7. Its just run 102000 miles I looked down into the inlet and the backs of the valves are clean only slight carbon considering these direct injection engines are prone to carbon build up up especially in USA where they have poorer fuel I was very happy with the state of them, it did have a small erratic idle occasionally just shook as if wind was blowing car but since I cleaned the throttle body it's gone. The tickover was 1500rpm after cleaning due to the ecu having setting the idle to the position the throttle flap was in due to the carbon build up on the opening flap had held it open slightly , so I pulled the ects and efi fuse which clears all ecu settings and started her up and back to 700rpm in gear and it runs so much better.
  8. ok so the plugs fitted today and oil and filter carried out and while she was in bits I cleaned the inlet manifold and throttle body , quick inspect of the backs of the valves that I could see and they had minimal carbon on them so happy put her back together reset ECU by removing ects and efi fuse quick road test feels very smooth and tick over a rock steady 700rpm.
  9. ok plugs arrived today and I have checked them out re: Fake and everything checks out I am sure they are genuine so in all very happy bear in mind these are an alternative to the original denso listing
  10. I emailed Ambush Parts today and they assured me they are genuine Denso they are an alternative to the expensive ones we are used to seeing but check I will when they arrive these are the guys seem legit : https://www.ambush.parts/
  11. https://www.denso.com/global/en/products-and-services/automotive-service-parts-and-accessories/plug/iridiumtt/crossreference.html These are compatible according to Denso so as long as I check them against the "fake checker" link I should be ok.
  12. I did and I also watched the link to the fake plugs and looking at the pics they look genuine to me but when they get here I will check them and if they are not then eBay will be handling it .
  13. I just bought 6 x IKBH20TT of ebay for £36 with discount for multibuy delivered free bargain. company called Ambush-Parts https://www.ebay.co.uk/itm/323973417950
  14. I picked up a compressor on ebay and fitting was very easy jack car up and remove under tray two 10mm bolts holds pipes on and four 12mm fix it to the block it drops right out of the bottom. I had it gassed at a local garage full vacuum and gas pressure test and dye added and correct amount of oil in system. Luckily I did not have to replace the dryer as I had only allowed the system to be empty a few days. The compressor may only last a year or maybe more as I have no idea what the miles are on the S/H unit.
×
×
  • Create New...