Check out the beading on that!!

[NothernDan]

Show us your finest beading pics! @Flytvr I’m expecting some museum quality productions from you!!

The below was achieved using Meguiars Waterless Wash and Wax last night, a pretty decent result considering no actual “rubbed in” wax was used. I tend to get the best results (for my car colour) from my own personal favourite, Dodo juice ‘light fantastic’ soft wax, applied over a coat or two of Colinite 476S. These two combined give much better uniform beading for a few months without any reapplication required and much tighter beading than that shown below. I find I then just need the occasional once over with the Meguiars stuff mentioned above to keep on top of things.

Show us yours this fine rainy day.

 

[rayaans]

Things like Carpro Hydro2 would knock it out of the park though and arguably are easier to use.

[NothernDan]

1 hour ago, rayaans said:

Things like Carpro Hydro2 would knock it out of the park though and arguably are easier to use.

😎 Googling it now!! 

[Richiano]

Auto Finesse Tripple then Collinite 476s.

[Big Rat]

@NothernDan Dan does it matter about the colour of the beading as technically this stuff is beading is it not.........

🐁

[Mattmech]

[NemesisUK]

Flat beading? (frost  )

[NothernDan]

4 hours ago, Mattmech said:

And we have a winner!!

I'd say that was bead-tastic!

[NothernDan]

4 hours ago, Big Rat said:

@NothernDan Dan does it matter about the colour of the beading as technically this stuff is beading is it not.........

🐁

Jesus! Cold down there today! 

[Mattmech]

17 minutes ago, NothernDan said:

And we have a winner!!

I'd say that was bead-tastic!

Had to wait for it to start ☔️ 

This stuff is very good for your beading pleasure. Bit tacky when it’s on as the car does seem to ‘hold’ any dust.

nice and cheap at ecp too.

[rayaans]

6 minutes ago, Mattmech said:

Had to wait for it to start ☔️ 

This stuff is very good for your beading pleasure. Bit tacky when it’s on as the car does seem to ‘hold’ any dust.

nice and cheap at ecp too.

Stick the product code into Car parts 4 less and see what happens..... lol

[First_Lexus]

Pro applied GTechniq ceramic coating with C2v3 applied over the top to finish, albeit not for a few weeks...nothing sticks to my Lexus!

 

[NemesisUK]

Williams Ceramic coating with Meg's Synthetic X-press spray wax. Video is 18mths old but the finish looks exactly the same

 

Meg's tops the lot of you!

 

[Guest]

Sorry[mention=1300]nemesisUK[/mention] game over.....

 

Sent from my STV100-4 using Tapatalk

 

 

 

 

[Flytvr]

On 10/6/2018 at 11:04 AM, NothernDan said:

Show us your finest beading pics! @Flytvr I’m expecting some museum quality productions from you!!

Now there’s a challenge.

However, there’s no way I’m getting a hose pipe in my garage, and as of tonight the F is hibernating for the Winter.😁

[rayaans]

 

 

[NothernDan]

13 hours ago, Comedian said:

Sorry[mention=1300]nemesisUK[/mention] game over.....

 

Sent from my STV100-4 using Tapatalk

 

 

 

 

What a picture!! 😎

[J Henderson]

Here's my effort. [emoji3]

Sent from my SM-G935F using Tapatalk

[oneflewover]

Snuck this in here, Sonax quick detailer

[Big Rat]

@oneflewover Paul a bit of modern art going on there 😂

🐀

[GogCymru]

I had to wait for rain, then it stopped... i use autoglym: super resin polish, extra gloss sealer, then just keep on top of things with the polar hlast foam and then shampoo & conditioner.

[d3ron]

Bit of a cheat really as I've done nothing to the car yet, until I get it touched up. But a nice bit of dew this morning. 

[Twellsie]

couldn't resist......

 

 

 

 

[scudney]

[ColinBarber]

NemesisUK and rayanns are the winners. Beading is bad for your paintwork; the water, and contaminants, are in touch with the surface for a very long time as it takes an age for the bead to evaporate, damaging the top coat, and once if finally does dry you are left with water marks. Products that sheet the water and let it run off are superior.